Built-in Low Voltage Controls for Electric Screens

Choose from one of the following:

View All Controls High Voltage Controls Low Voltage Controls Built-in Low Voltage Controls Access MultiView Controls 220 Volt Controls

ILT Extra IR Transmitter

ILT Extra IR Transmitter

Part number: 121170

ILT Extra IR Transmitter

U.S. Retail Price $100


ILT IR Transmitter/Receiver

ILT IR Transmitter/Receiver

Part number: 121169

The ILT IR is an Infrared (IR) transmitter and receiver. 3-button operation for instant access to "up", "down", and "stop" functions. Fully compatible with "learnable" IR master control systems. The IR receiver plugs into the terminal block in the screen housing.

U.S. Retail Price $133


ILT RF Transmitter/Receiver

ILT RF Transmitter/Receiver

Part number: 121167

The ILT RF is a hand-held RF transmitter. 3-button control lets you change direction or adjust format at any point. The RF receiver plugs into the terminal block in the screen housing.

U.S. Retail Price $258


Low Voltage Wall Switch

Low Voltage Wall Switch

Part number: 121171

This wall switch is for motors with built-in low voltage and features three buttons for “up”, “stop”, and “down” control. It is supplied with a 25’ RJ9 data cable. It also features 4 quick connect terminals to connect your own four conductor wire. The Low Voltage Wall Switch is necessary to set/adjust the motor limits and is supplied with the screen. Additional Low Voltage Wall Switches can be added to the screen in parallel.

U.S. Retail Price $58

  Instructions PDF document
  Tech Data Sheet PDF document

LVC-IV & LVC-S

LVC-IV & LVC-S

Part number: 121223

Kit contains one (1) LVC-IV control Module and one (1) LVC-S low voltage switch. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways
  • Low voltage wall switch
  • "dry" contact closure
  • RF (radio frequency)
  • IR (infrared)
  • Serial Communication
  • low voltage relay (3v-28v)

Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch.

The LVC-IV is housed in a single box, 3-compartment and UL Listed. A low voltage switch (LVC-S) is included. The module contains:

  • a 3-screw terminal block for a low voltage wall switch
  • an IR receiver jack
  • a built-in RF receiver
  • two-RJ25 ports for RS232/RS485
  • a low voltage relay port with cable
  • user-serviceable 3.5 A fuse

The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $262

  110V Tech Data Sheet PDF document
  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV (Low Voltage Control Module)

LVC-IV (Low Voltage Control Module)

Part number: 121222

The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways:
  • Low voltage wall switch
  • "dry" contact closure
  • RF (radio frequency)
  • IR (infrared)
  • Serial Communication
  • low voltage relay (3v-28v)

Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch.

The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains:

  • a 3-screw terminal block for a low voltage wall switch
  • an IR receiver jack
  • a built-in RF receiver
  • two-RJ25 ports for RS232/RS485
  • a low voltage relay port with cable
  • a user-serviceable 3.5 A fuse
The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $218

  110V Tech Data Sheet PDF document
  CAD (dwg) AutoCAD document
  CAD (pdf) PDF document
  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV/IRT Kit

LVC-IV/IRT Kit

Part number: 121234

Kit contains one (1) LVC-IV control Module, one (1) IR Transmitter and one (1) IR Receiver. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways: Low voltage wall switch, "dry" contact closure, RF (radio frequency), IR (infrared), Serial Communication or low voltage relay (3v-28v). Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch. The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains a 3-screw terminal block for a low voltage wall switch, an IR receiver jack, a built-in RF receiver, two-RJ25 ports for RS232/RS485, a low voltage relay port with cable and a user-serviceable 3.5 A fuse. The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $305

  110V Tech Data Sheet PDF document
  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV/WRT Kit

LVC-IV/WRT Kit

Part number: 121233

Kit contains one (1) LVC-IV control Module and one (1) RF Transmitter. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways: Low voltage wall switch, "dry" contact closure, RF (radio frequency), IR (infrared), Serial Communication or low voltage relay (3v-28v). Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch. The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains a 3-screw terminal block for a low voltage wall switch, an IR receiver jack, a built-in RF receiver, two-RJ25 ports for RS232/RS485, a low voltage relay port with cable and a user-serviceable 3.5 A fuse. The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $305

  110V Tech Data Sheet PDF document
  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-S with Locking Cover

LVC-S with Locking Cover

Part number: 121232

The LVC-S with Locking Cover Plate is a 3-button (Up, Stop, Down) wall switch which controls LVC III. Three individual Single Pole, Single Throw contacts (On/Off). Momentary action. The buttons are oval. The locking cover plate is metal, and provided with a lock and key. It fits a single-gang box. There are no wire leads: there are screw terminals on the back for Down, Common, and Up.

U.S. Retail Price $132

  Tech Data Sheet PDF document

VIC-12 (Video Interface Control)

VIC-12 (Video Interface Control)

Part number: 121024

Allows screen to be controlled by projector switch. When the projector comes on, the screen descends automatically. The VIC-12 interfaces screen operation with a video projector or tuner featuring a 12V switched outlet.

The VIC may be built into Access V & E. Factory installed controls will increase the length of the case. Call for exact case length as this dimension is critical.

The VIC-12 can be purchased with an override switch (VIC-OS), permitting independent operation. A VIC is not compatible with an LVC-IV, built-in or otherwise.

U.S. Retail Price $143

  Tech Data Sheet PDF document

VIC-6 (Video Interface Control)

VIC-6 (Video Interface Control)

Part number: 121025

Allows screen to be controlled by projector switch. When the projector comes on, the screen descends automatically. Model VIC-6 interfaces screen operation with a video projector or tuner featuring a 6V switched outlet. The VIC may be built into Access V & E. Factory installed controls will increase the length of the case. Call for exact case length is this dimension is critical.

The VIC-6 can be purchased with an override switch (VIC-OS), permitting independent operation. A VIC is not compatible with an LVC-IV, built-in or otherwise.

U.S. Retail Price $143

  Tech Data Sheet - 220V PDF document


Quick Feedback

We would love to get your thoughts so don't hesitate to send us your feedback!

Name
Email
What could we improve? (required)