Controls for Electric Screens

Choose from one of the following:

View All Controls High Voltage Controls Low Voltage Controls Built-in Low Voltage Controls Access MultiView Controls 220 Volt Controls

3-Position Key Control Switch  KS-3

3-Position Key Control Switch KS-3

Part number: 121018

Where the "up" and "down" directional functions need to be combined with the security of a key switch, the 3-Position Key Control Switch KS-3 offers limited screen access. The KS-3 is intended as the sole control station and cannot be used as a multiple station control.

U.S. Retail Price $98

  Tech Data Sheet PDF document

AMV-C

AMV-C

Part number: 121048

For low voltage independent control of Access MultiView screen and masking motors. Motors are controlled by independent 3-button switches in a single box.

U.S. Retail Price $550


AMV-IR

AMV-IR

Part number: 121052

The Access MultiView screen and the masking system are independently controlled. The AMV-IR has two multi-channel infrared controls, two receivers and one transmitter.

U.S. Retail Price $828


AMV-IRW

AMV-IRW

Part number: 121053

The Access MultiView screen and the masking system are independently controlled. The AMV-IRW has an IGC/3N1 controller, two wall switches with built-in IR receivers and one IR transmitter.

U.S. Retail Price $785


Control Station MS-4R

Control Station MS-4R

Part number: 121005

Draper MS-4R multiple-station controls are identical in appearance to Draper's SS-1R Single Station Control. Automatic override allows only one signal to reach the motor when switches are operated simultaneously. 115V current. Also available in 220V.

U.S. Retail Price $63


Ethernet to Serial Bridge LS101

Ethernet to Serial Bridge LS101

Part number: 121276

The LS100 is a wired serial device that connects RS-232 based serial devices to a 10-Base-T Ethernet Network. Uses a DB9 serial port for connection to serial, RJ45 Ethernet connector for the network.

U.S. Retail Price $715


ILT IR Transmitter

ILT IR Transmitter

Part number: 121170

ILT Extra IR Transmitter

U.S. Retail Price $102


ILT IR Transmitter/Receiver

ILT IR Transmitter/Receiver

Part number: 121169

The ILT IR is an Infrared (IR) transmitter and receiver. 3-button operation for instant access to "up", "down", and "stop" functions. Fully compatible with "learnable" IR master control systems. The IR receiver plugs into the terminal block in the screen housing.

U.S. Retail Price $137


ILT Replacement 4 jack splitter

ILT Replacement 4 jack splitter

Part number: C156.096

ILT Replacement 4 jack splitter

U.S. Retail Price $53


ILT RF Transmitter/Receiver

ILT RF Transmitter/Receiver

Part number: 121167

The ILT RF is a hand-held RF transmitter. 3-button control lets you change direction or adjust format at any point. The RF receiver plugs into the terminal block in the screen housing.

U.S. Retail Price $263


ILT RF Transmitter/Receiver

ILT RF Transmitter/Receiver

Part number: 121168

The ILT RF is a hand-held RF transmitter. 3-button control lets you change direction or adjust format at any point. The RF receiver plugs into the terminal block in the screen housing.

U.S. Retail Price $160


ILT Single-Station Low-Voltage Key Wall Switch

ILT Single-Station Low-Voltage Key Wall Switch

Part number: 121179

ILT Optional 3 Position Single Station Low Voltage Key Wall Switch (momentary)

U.S. Retail Price $153


ILT Single-Station Low-Voltage Wall Switch with Locking Cover Plate

ILT Single-Station Low-Voltage Wall Switch with Locking Cover Plate

Part number: 121185

ILT Optional Single Station Low Voltage Wall Switch w/locking cover plate

U.S. Retail Price $153


Infrared Remote Transmitter IRT

Infrared Remote Transmitter IRT

Part number: 121228

Infrared transmitter (IRT) for use with the new LVC-IV Low Voltage Control. Requires a compatible receiver.

U.S. Retail Price $72

  IR Remote Control Wiring Instructions PDF document

IRT/R

IRT/R

Part number: 121227

The IRT/R is an Infrared (IR) transmitter/Receiver kit for use with the new LVC-IV Low Voltage Control. Fully compatible with "learnable" IR master control systems. Kit includes one Infrared Transmitter and one Infrared Receiver.

U.S. Retail Price $88

  IR Remote Control Wiring Instuctions PDF document

KS-1

KS-1

Part number: 121017

To ensure a certain level of security, KS-1 features a key-operated power supply switch for limited screen access. It is intended for use with the SS-1R single station control, or MS-3R and MS-4R multiple station controls, where the safety feature of key control is also required.

U.S. Retail Price $88

  Tech Data Sheet PDF document

KS-1/SS-1R

KS-1/SS-1R

Part number: 121032

Where the safety feature of key control is required, the KS-1/SS-1R combines a power supply key switch and a single station rocker switch into one kit. KS-1 is designed to be used in conjunction with another control. It mounts next to an operating switch and offers a key-operated power supply switch that limits screen access. The key switch can interrupt power to the rocker switch. The SS-1R is intended as the sole control station and can be used with the KS-1 power supply key switch for added security. It cannot be used as a multiple station control.

U.S. Retail Price $152


LVC-IV & LVC-S

LVC-IV & LVC-S

Part number: 121223

Kit contains one (1) LVC-IV control Module and one (1) LVC-S low voltage switch. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways
  • Low voltage wall switch
  • "dry" contact closure
  • RF (radio frequency)
  • IR (infrared)
  • Serial Communication
  • low voltage relay (3v-28v)

Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch.

The LVC-IV is housed in a single box, 3-compartment and UL Listed. A low voltage switch (LVC-S) is included. The module contains:

  • a 3-screw terminal block for a low voltage wall switch
  • an IR receiver jack
  • a built-in RF receiver
  • two-RJ25 ports for RS232/RS485
  • a low voltage relay port with cable
  • user-serviceable 3.5 A fuse

The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $267

  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV (Low-Voltage Control Module)

LVC-IV (Low-Voltage Control Module)

Part number: 121222

The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways:
  • Low voltage wall switch
  • "dry" contact closure
  • RF (radio frequency)
  • IR (infrared)
  • Serial Communication
  • low voltage relay (3v-28v)

Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch.

The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains:

  • a 3-screw terminal block for a low voltage wall switch
  • an IR receiver jack
  • a built-in RF receiver
  • two-RJ25 ports for RS232/RS485
  • a low voltage relay port with cable
  • a user-serviceable 3.5 A fuse
The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $223

  CAD (dwg) AutoCAD document
  CAD (pdf) PDF document
  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV/IRT Kit

LVC-IV/IRT Kit

Part number: 121234

Kit contains one (1) LVC-IV control Module, one (1) IR Transmitter and one (1) IR Receiver. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways: Low voltage wall switch, "dry" contact closure, RF (radio frequency), IR (infrared), Serial Communication or low voltage relay (3v-28v). Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch. The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains a 3-screw terminal block for a low voltage wall switch, an IR receiver jack, a built-in RF receiver, two-RJ25 ports for RS232/RS485, a low voltage relay port with cable and a user-serviceable 3.5 A fuse. The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $312

  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-IV/WRT Kit

LVC-IV/WRT Kit

Part number: 121233

Kit contains one (1) LVC-IV control Module and one (1) RF Transmitter. The LVC-IV low voltage control is used to control one 115V motor by a third party system in a variety of ways: Low voltage wall switch, "dry" contact closure, RF (radio frequency), IR (infrared), Serial Communication or low voltage relay (3v-28v). Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch. The LVC-IV is housed in a single box, 3-compartment and UL Listed. The module contains a 3-screw terminal block for a low voltage wall switch, an IR receiver jack, a built-in RF receiver, two-RJ25 ports for RS232/RS485, a low voltage relay port with cable and a user-serviceable 3.5 A fuse. The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $312

  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

LVC-S

LVC-S

Part number: 121225

The LVC-S (Low Voltage Control Station) is a 3-button control switch for use with the LVC-IV. It features three buttons for "up", "stop" and "down" control. Quick connect terminals on the back of the switch connect to the LVC-IV using your own 4-conductor wire.

U.S. Retail Price $63

  CAD (pdf) PDF document

LVC-S with Locking Cover

LVC-S with Locking Cover

Part number: 121232

The LVC-S with Locking Cover Plate is a 3-button (Up, Stop, Down) wall switch which controls LVC III. Three individual Single Pole, Single Throw contacts (On/Off). Momentary action. The buttons are oval. The locking cover plate is metal, and provided with a lock and key. It fits a single-gang box. There are no wire leads: there are screw terminals on the back for Down, Common, and Up.

U.S. Retail Price $135

  Tech Data Sheet PDF document

MS-3R/MS-4R

MS-3R/MS-4R

Part number: 121002

The MS-3R/MS-4R provides the ability to control one projection screen from multiple locations using the motor’s voltage. For multiple control stations, either 3- or 4-wire versions of the MS-4R are utilized. The MS-4R is the first control station and also the intermediate control(s), with the MS-3R being the last control station in the series. Automatic override allows only one signal to reach the motor when switches are operated simultaneously. Not intended for use with any other controls.

U.S. Retail Price $123

  Tech Data Sheet PDF document

Network Serial Communication LVC-IV & LS101 Kit

Network Serial Communication LVC-IV & LS101 Kit

Part number: 121277

Kit combines LVC-IV low voltage control module and LS101 Ethernet bridge for control of a single 110v motor on a network. The LS101 is a wired serial device that connects RS-232 based serial devices to a 10-Base-T Ethernet Network. Uses a DB9 serial port for connection to serial, RJ45 Ethernet connector for the network.

U.S. Retail Price $940


R2D7 for RS232 Serial Control

R2D7 for RS232 Serial Control

Part number: C156.066

The serial bridge allows third party control of our low voltage control via serial RS-232 ASCII commands.

U.S. Retail Price $193

  Instructions PDF document

SP-KPS-I

SP-KPS-I

Part number: 121019

When “up” and “down” directional functions need to be secured, the SP-KPS-1 features a 3-position control switch with a locking cover plate for limited screen access. It is intended as the sole control station and cannot be used as a multiple station control. It is not intended for use with any other control.

U.S. Retail Price $117

  Tech Data Sheet PDF document

SP-KSM

SP-KSM

Part number: 121022

Where momentary spring-loaded action is required, the KS-3 replaces the standard 3-position key switch. The SP-KSM combines the “up” and “down” directional functions with the security of a key switch to provide limited screen access. It can be used for low-voltage contact closure or multiple switching. The SP-KSM ships standard with Scissor Lift, and is necessary to access Scissor Lift service positions.

U.S. Retail Price $98

  SPKSM Technical Data Sheet PDF document
  Tech Data Sheet PDF document

SS-1R

SS-1R

Part number: 121001

Standard control included with Draper 110V electric screens, the SS-1R is intended as the sole control station. It cannot be used as a multiple station control.

U.S. Retail Price $65

  CE Tech Data Sheet PDF document
  Tech Data Sheet PDF document

Wall Switch SS-1R (White)

Wall Switch SS-1R (White)

Part number: 121102

The Wall Switch SS-1R (White) is intended as a sole control station for Draper 110V electric screens. It cannot be used as a multiple station control.

U.S. Retail Price $65

  CE Tech Data Sheet PDF document
  Tech Data Sheet PDF document

Wireless Transmitter, RF type, WRT

Wireless Transmitter, RF type, WRT

Part number: 121226

Hand-held radio frequency transmitter (WRT). 3-button control lets you stop or change direction at any point. For use with LVC-IV Low Voltage Control Module.

U.S. Retail Price $72

  RF Remote Control Wiring Instructions PDF document

Low-Voltage Control with 2 Switches LVC-IV, 2 LVC-S

Low-Voltage Control with 2 Switches LVC-IV, 2 LVC-S

Part number: 121224

Kit contains one (1) LVC-IV control Module and two (2) LVC-S low voltage switches. The LVC-IV low voltage control is used to control one 115V/220V motor by a third party system in a variety of ways:
  • Low voltage wall switch
  • "dry" contact closure
  • RF (radio frequency)
  • IR (infrared)
  • Serial Communication
  • low voltage relay (3v-28v)

Works with LVC-S, WRT, IRT/R, SP-KSM, Aux. "dry" contacts and KS-1 Power Supply Switch. The LVC-IV is housed in a single box, 3-compartment and UL Listed. Two low voltage switches (LVC-S) are included. The module contains a 3-screw terminal block for a low voltage wall switch, an IR receiver jack, a built-in RF receiver, two-RJ25 ports for RS232/RS485, a low voltage relay port with cable and a user-serviceable 3.5 A fuse.

The LVC-IV (module only) may be built into Access (Access Fit, Standard Access and Access XL) V & E, Signature V & E, Ultimate Access V & E, Silhouette V & E, Premier, Targa and Envoy. Factory installed controls will increase the length of the case in the Premier and Targa. Call for exact case length if this dimension is critical.

U.S. Retail Price $312

  Dry Contact Wall Switch Wiring Instructions PDF document
  IR Remote Control Wiring PDF document
  Low Voltage Controls Wiring Instructions PDF document
  Low Voltage Controls Wiring Instructions (230V) PDF document
  LVC IV 110V Tech Data Sheet PDF document
  LVC IV 220V Tech Data Sheet PDF document
  RF Remote Control Wiring PDF document

Low-Voltage Wall Switch

Low-Voltage Wall Switch

Part number: 121171

This wall switch is for motors with built-in low voltage and features three buttons for “up”, “stop”, and “down” control. It is supplied with a 25’ RJ9 data cable. It also features 4 quick connect terminals to connect your own four conductor wire. The Low Voltage Wall Switch is necessary to set/adjust the motor limits and is supplied with the screen. Additional Low Voltage Wall Switches can be added to the screen in parallel.

U.S. Retail Price $60

  Instructions PDF document
  Tech Data Sheet PDF document

VIC-12 Kit (Video Interface Control)

VIC-12 Kit (Video Interface Control)

Part number: 121033

Video Interface Control - a relay with a COM/NC/NO contacts, and a 12 V coil, housed in a metal box for the Revelation screen.

U.S. Retail Price $143

  Tech Data Sheet PDF document


Quick Feedback

We would love to get your thoughts so don't hesitate to send us your feedback!

Name
Email
What could we improve? (required)