IntelliFlex® Control System Components

Motor Controls - Gen 3

The IntelliFlex® Shade Control System is the system with real brains, it is the most sophisticated high voltage system on the market. Programmable through IR transmitters, PCs, and keypads, you can control the system through the internet, IR transmitters, PCs, sun and wind sensors, timers and wall keypads. Relays and controls are the most compact in the industry.

  • Gen 3 controls will not work with Gen 2 controls. We are phasing out Gen 2 and Gen 3 is the newest generation. Gen 2 is still being used for replacements and expansions.
  • Activate up to four intermediate stops with the SCI or SPGC4. Automatic recalibration when shades go to upper or lower limits.
  • Can be installed in group panel, or individually in junction boxes-drastically simplifies wiring requirements.
  • All IntelliFlex® components carry a Five Year Guarantee (excluding timer and touchpad IR transmitter).

ISO (Isolating Relay) - Gen 3

Part Number: C157.0116

Click image to enlarge.

Isolating Relay allows control of single shade—one isolating relay is used per motor. However, you can also daisy chain up to 12 Isolating Relays, and control them using a single line 15 amp voltage (110-120V) switch. The Isolating Relay can also be used if existing motors are failing due to inadequate pre-wired installations (i.e., not enough wires pulled to motors). Operated by line voltage switch (SPDT only).

SC1 - Gen 3

Part Number: C156.168

Click image to enlarge.

The SC1 is a smart control for one motor. It allows one motor to have up to four preset stops from a switch and more for a communication interface (CI). Each SC1 can belong to any input or switch button on the BUS line. It is not limited to a certain number of addresses. The SC1 has a micro USB hub on it for plugging in input devices. It also has a set of dry contacts and RJ11 blocks for BUS communication. All SC1s needing to communicate with each other will need a CAT 5 line going between them with an RJ 11 termination. This BUS line will carry communication to all SC1s linked to it.

  • PC is required for programming
  • Contact Draper for programming cable.

GC4 - Gen 3

Part Number: C156.172

Click image to enlarge.

Four 110-120V, single-motor electronic “isolating relays”, the GC4 is an inexpensive way of controlling multiple motors on a single switch. (Can be grouped together in banks of three, to control up to 12 motors, operating on a standard, SPDT 15-amp switch.) Wires stay where they are meant to through ETL-recognized, spring-loaded connection terminals—providing for an extremely fast and easy installation. Install individual relays to allow parallel wiring of multiple motors on one switch. This system does not allow for control/adjustment of individual motors or mid-window alignment positions, and is not suitable if different fabrics or tube diameters are being used in a single 4 motor panel. ETL listed enclosure included.

SGC1 - Gen 3

Part Number: C156.169

Click image to enlarge.

The SGC1 is a smart group control for one motor. It allows one motor to work with different groups from input devices. It cannot do preset stops. Each SGC1 can belong to any input or switch button on the BUS line. It is not limited to a certain number of addresses. The SGC1 has a micro USB hub on it for plugging in input devices. It also has a set of dry contacts and RJ11 blocks for BUS communication. All SGC1s needing to communicate with each other will need a CAT 5 line going between them, with an RJ 11 termination. This BUS line will carry communication to all SGC1s linked to it.

  • PC is required for programming
  • Contact Draper for programming cable.

SGC4 - Gen 3

Part Number: C156.171

Click image to enlarge.

The SGC4 is a smart group control of up to four motors. All motors connected to the SGC4 will operate as a group without preset stops or individual control. This unit allows for low voltage switching to operate the motors connected to an SGC4 together. An SGC4 can belong to any group on the BUS line. The SGC4 comes as an ETL approved assembly.

  • PC is required for programming
  • Contact Draper for programming cable.

SPGC4 - Gen 3

Part Number: C156.170

Click image to enlarge.

The SPGC4 is a smart programmable group control of up to four motors. It is designed to run up to four motors individually or as a group with presets available. An SPGC4 is four SC1 units in an enclosure to become an ETL assembly. The units inside an SPGC4 are already connected with CAT 5 so one only needs to connect SPGC4 boxes together.

  • PC is required for programming
  • Contact Draper for programming cable.